POWER CONNECTIONS OPS MODULE SELF-TEST
The AccuNav
II
works from a twelve-volt
battery system.
For the best
results,
attach the
power
cable
directly
to the
battery.
You can attach the
power
cable to an
accessory
or
power
buss,
however
you may
have
problems
with electrical interference.
Therefore,
it's saferto
go
ahead and
attach the
powercable directlyto
the
battery.
If the cable is too
short,
splice
#18
gauge
wire onto it. The
power
cable has four
wires; red, black,
green,
and white. Red
is
the
positive lead,
black is
negative
or
ground.
Make
certain to attach the in-line
fuse holder to the red lead as close to the
power
source as
possible.
For
example,
if
you
have to extend the
power
cable to
the
battery
or
power buss,
attach one end of the fuse holder
directly
to the
battery
or
power
buss. This will
protect
both the unit
and
the
power
cable
in the event of a short. The
AccuNav
II
uses a
3-amp
fuse.
IMPORTANT!
Do
not
use this
product
without a
3-amp
fuse wired into the
power
cable!
Failure to use a
3-amp
fuse will void
your warranty.
This feature tests the UPS module and returns a
special
code. This code
is of interest
only
to the service
department.
However,
the AccuNav II
interprets
this code and
displays
a status
message.
This
message
is either
"MODULE HAS PASSED" or "MODULE HAS FAILED" and shows at the
bottom
of
the
screen. The
current software
version number also
appears
near the bottom of the screen. Contact the
factory
customer service
department
if the module fails the self test. Do not
attempt
to use this
product
if
it
fails
the
self
test.
To use the self test
feature,
pressthe
MENU
keytwicewhile
it's in the UPS
mode,
then
press
the
key
next to the "UPS MOD-
ULE SELF TEST" label. The
screen shown at
right appears.
To
exit
from this
screen, press
the
CLEAR
key.
GPS SIMULATOR
This feature
places position
and
navigation
data on all
screens,
including
the
plotter.
The unit
"navigates"
a closed course. It shows
bearing
and
distance to
go,
course over
ground,
and other information. A
recurring
message appears, alerting you
that the simulator mode is enabled. Don't
navigate
when the simulator is on!
To turn the simulator
on,
press
the MENU
key
twice,
then
press
the
key
next to the "UPS SIMULATOR OFF ON" label. The simulator mode starts
immediately.
To turn the simulator
off,
either
press
and hold the OFF
key
or
repeat
the above
steps.
Press the
key
next to the "UPS SIMULATOR
OFF ON" label.
AccuNav II POWER CONNECTIONS
2
43
TO "P'
CONNECTOR
ON ACCUNAV II
P CPS SELF TEST
BIT SUMMARY 0000
LOW ORDER RAM FFFF
HIGH ORDER RAM FYFF
PRE PROCESS TEST 0000
PRE PROCESS RAM FEFF
MULTI INTERFACE 0000
LICO TEST 0000
SIGNAL INJS 0000
0FTWARE_VERSION
320
CLEARI
WHITE
WIRE
TO
NMEA
INTERFACE
MODULE HAS PR RED
RED
WIRE
3
amp
FUSE
DOPS
BEACON
RECEIVER
PDF compression, OCR, web-optimization with CVISION's PdfCompressor
(140 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals