Eagle ACCUNAV 2 Specifications Page 17

  • Download
  • Add to my manuals
  • Print
  • Page
    / 26
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 16
IMPORTANT!
Turning
the arrival alarm off
prevents
the AccuNavll from
sequencing
to
the next
waypoint
in the route.
This,
in
effect,
turns the route off.
However,
the unit will still show
navigation
data to the current
waypoint
in the route
at the time the arrival alarm was turned of f.
CANCEL NAVIGATION
To
stop
the AccuNav II from
navigating
to
waypoint
or
navigating
to a
waypoint
in a
route,
press
the MENU
key
twice. Now
press
the
key
next
to the "CANCEL NAVIGATION" label. This
stops
all
navigation.
NOTE:
Canceling navigation
does not erase the route or
any waypoints
from
memory.
It
merely stops
the AccuNav II from
navigating.
MODIFYING A ROUTE
Any part
of a route can be
changed
at
anytime.
For
example, suppose you
have a route
consisting
of
waypoints
number
1, 2,
and 3 and
you
wish to
changewaypoint numberatowaypoint
number5.
Simplypressthe
MENU
key,
then
press
the
key
next to the "More" label.
Next,
press
the
key
next
to
the "Route
Planning"
label.
Finally, press
the
key
next to the "Recall
Route" label.
Route number one
appears
on the
right
side of the screen.
The list of
waypoints
used in the route are shown beneath the route number
and name.
Using
the
down arrow
key,
movethe black boxto
waypoint
number
3. Now
press
the
key
next to the
"CHANGE" label.
Use the numbered
keys
to
change
the
waypoint
from 3 to
5.
Next,
press
the
key
next to
the "ACCEPT" label. You've
changed
the
waypointfrom
3
to
5.
Finally, press
the
key
next to
the "EXIT" label
and
you're
fin-
ished.
.OUTE it
1
tJSIEL.
NAME: JPiYS COLJE
PIE
RSE
!
1 BUOY 1
2 BUOY2
SANDY PT
i
Remember,
any
pad
of the route can be
changed
at
any
time.
searching
forthe
satellite,
then a"S"
appears.
ELV is the elevation
(height)
of the satellite above the horizon from
your position.
AZM is the azimuth
or direction of the satellite from
your position.
For
example,
if the azimuth
of a satellite is 180
degrees,
then it is due south.
SNR is the
signal-to-noise
ratio. This tells
you
how
strong
the satellite's
signal
is.
The
higherthe
SNR
number,
the better.
The satellites that are visible in the
sky
from
your
position
are shown in the
lower
right
corner of the screen under the "VISIBLE
SATS"
heading.
In the lower
left corner of the screen are the DOPS
displays.
These show
you
the "Dilution Of Precision"
(DOP)forthe
horizontal
(1-IDOP), geometric
(GDOP), position (PDOP),
time
(TDOP),
and vertical
(VDOP).
The GDOP
is the combination
value of
HDOP,
VDOP,
and
TDOP. The smaller the
GDOP's
number
is,
the better. The GPS receiver selects satellites based
on
GDOP,
therefore
it
always
tries to use satellites that have
good
DOP
values.
These
depend
on the azimuth and elevation
of the
satellite,
and
any ground
based obstructions.
Remember,
the smaller the number
-
the better on all
of the DOPs.
POSITION SCREEN
The
position
screen
automatically appears
after the AccuNav II is initial-
ized or
you
can view this screen
at
any
time
by pressing
the PUS
key.
The
position display
shows
your present
position,
course over
ground (COG),
cross track error
(XTE), bearing (BRG),
and local time.
Your
present position displays
near the
top
of the screen in latitude!
longitude
coordinates. This
is
minute. For
example,
on this
page,
the
present position
is 31
degrees,
8.642 minutes latitude
and 82
degrees,
50.853 min-
utes
longitude.
Below the
present position
on the left side
is the
Bearing
to
Waypoint
(BRG) display.
This is
ex-
pressed
in
degrees
true or
magnetic, depending
on the
_____________
mode the AccuNav II is in.
To
the
right
of the
Bearing
is the
Course Over Ground
(COG)
display.
32 13
shown in
minutes,
and thousandths of a
U U
N
36°08.856'
U 95°50.496'
jOM287OM
2:S:32
PMHIL
0101
mi
PDF compression, OCR, web-optimization with CVISION's PdfCompressor
Page view 16
1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 25 26

Comments to this Manuals

No comments