Eagle Mach 1 Specifications download pdf (Page 1)

—

the

stylus may

damaged. (See Figurel9.)

SPECIAL NOTE: The

stylus

may

damaged

if the

platen

assembly

pulled

down un-

less the

stylus

has been

moved to the back side of the

platen.

4. Pull out and down on

the

tab

at the

top

center of the

platen

assembly

expose

the

pa-

per spools. (See Figure2o.)

5. To remove the full

take-up

roll

and the

empty supply spool,

press

the two metal tabs to-

gether

on the

top

of the

platen

assembly,

and

pull

out and

down on the

paper

retainer.

(See Figure 21.)

The full take-

roll can now be

easilly

re-

moved from the

paper

core

shafts.

(See Figure 22.)

6. Pull the

empty supply

core

from the

right

side in the

same manner. Install

the

empty

core onto the

take-up

shaft.

(See Figure

23)

Align

the two notches in

the

core with the tabs on the

lower

take-up spool.

7. Slide a fresh roll of

paper

position

on the

supply

side

•

shaft on the

right

side of the

•

platen assembly.

The

paper

must

spool

off the bottom of

the roll.

(See Figure 24)

8. Draw the end of the

paper

across the face of the

platen,

around the friction

roller,

over

the

take-up

core,

and

tape

squarely

to the

take-up

core.

(See Figure 25)

Small

pieces

tape may

be stored inside

the

housing

for this

purpose.

Close the

top

of the

platen

assembly by pressing

the two

tabs

together

on the

paper

retainer and

returning

the re-

tainer back

to the

operating

position. (See

Figure26)

9. Turn the small knob at the

upper

left hand side of the

platen assembly

put

small amount of tension on

the

paper.

It should be

snug

against

the

platen. ( Figure

27)

10. Push the

platen assembly

back to its

operating position.

Be sure it

engages

the catch

inside the

top

of the case.

(See Figure2O)

11. Close the front of the case.

Latch both catches on the

top

of the case.

12. Turn the unit on. Move the

Chart

Speed

knob

fully

clock-

wise. Watch the

paper long

enough

to be sure it is mov-

ing smoothly

and

evenly

across the

platen.

If the

pa-

per

flutters or

begins

to run

"uphill", repeat step

Figure

Notice—Use

only genuine

Eagle

EGP-1

graph paper

Substitute

paper

does not

give

satisfactory performance

Eagle graph

recorders.

PDF compression, OCR, web-optimization with CVISION's PdfCompressor

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - ( Figure

— the stylus may be damaged. (See Figurel9.) SPECIAL NOTE: The stylus may be damaged if the platen assembly is pulled down un- less the stylus has bee

Page 2 - 1 can detect

I? - LJLI A P - ic & !t&!i L.± Figure 43 RANGE: 60 FEET SENSITIVITY: 3/4 SUPPRESSOR: MINIMUM PAPER SPEED: MAXIMUM LINES: OFF ZOOM: OFF GRAYLI

Page 3 - 2 to 3 feet of

Page 4 - &___300

EAGLE INSTALLATION AND OPERATION MANUAL flT JJLJ jjJ dAn I flA fi • / MADAINUS A EAGLE ELECTRONICS LIThO USA P0. BOX 669, CATOOSA, OKLA. 74015 988-00

Page 5 - LINES "ON"

STYLUS REPLACEMENT CAUTION — High voltage is pre- sent in the electronic section when the unit is turned on.' 1. TURN THE UNIT OFF. 2. Release b

Page 6 - Iff...!J'1!Ijii —

Occasionally, when changing the stylus or stylus belt, the zero does not print at the same place near the top of the chart paper. By rotating the BOTT

Page 7 - SENSITIVITY: TOO LOW

wheels by reversing the proce- dure used to remove the old one. BE SURE the fingers of the new stylus are pointed UP. 6. Close the front of the case.

Page 8 - A service

sound pulse has to travel, the weaker it becomes. By broaden- ing the pulse width, in essence, a larger signal is transmitted and it is easier for the

Page 9

lines immediately. Turn the range control back to your original depth setting. To turn the lines back on, simply reverse the procedure by turning the

Page 10 - !t&!i

Figure 3 BASIC OPERATION ON-OFF and SENSITIVITY Control Rotate the ON/OFF knob clock- wise to turn the unit on. The Sen- sitivity knob works much like

Page 11 - DIAGRAM & PARTS LIST

tional features that you have pro- grammed in. Just remember, if you have turned the lines and the scales off, and you wish to turn only the scales ba

Page 12 - EAGLE ELECTRONICS

1. INTRODUCTION Small boat sonar systems are routinely used to measure water depth, examine bottom contours, and locate fish. The Eagle MACH 1 recorde