Eagle ET-CSWESU2-BK User Manual

[ ET-CSWESU2-BK ] Eagle | Consus W-Series SATA to USB2.0 & eSATA External Storage System User Manual www.eagle-techusa.com

93 Connecting the External Hard Drive Attention:¾ Make sure power switch is OFF when attempt to connect DC power supply socket to the external hard dr

10Powering Up the Drive Press the power switch to turn on the unit. Wait 3 seconds after blue light illuminates. Windows 2000/XP/2003/Vista Your opera

11 4 Partition & Format the Hard DriveWindows XP/2000/2003 Note: For formatted Hard Drive, proceed to step 2. 1. Click the Start button and click

124. On the next page, choose your partition size then click Next.5. After that, please assign a drive letter for the new Hard Drive, and go to Next

13Allocation unit size as default. Assign a name in Volume label. Check the Perform a quick format to reduce format time. Click Next.7. Confirm your

1410. Go to My Computer, your new drive should be listed there and ready to use.Mac OS X Note: If the warning does not show up, start at step 2. 1. A

153. Under the Disk Utilities, choose the new hard drive (1) and click Partition (2). Click Options to choose format other than Mac Extended(3) refer

16Figure 1: 3 Options… Choose the partition for you hard drive. Click OK.Figure 2: 6 Format: Choose the format for your hard drive. 4. After the pa

175 Disconnecting the Hard DriveCAUTION: To prevent data loss, be sure to close all active applications before shutting down the drive. Windows XP/200

18Windows 98SE 1. Close all the application on Windows. 2. Be sure the drive isn’t running, press Power switch to shutdown the devices.3. Disconnec

1Index1 Getting Started Package Contents …………………………………………...……. 02 System Requirements ………………………………………….. 03 Updating Your Operating System ………

196 TroubleshootingTo search the EAGLE | CONSUS technical support knowledge base and to view a complete list of FAQs for your operating system, visit

20Q: What is JBOD, RAID? A: Redundant Array of Independent Disks (RAID); a collection of storage disks with a controller (or controllers) to manage th

21reporting the drive is busy or in use. A: This is usually caused by a program that is trying to read from the drive. Be sure to close all applicatio

22 If there is a pop-up when trying to transfer data, then click on allow option for requests from the USB or 1394 port. That will open the USB / 1

23Q: Why my Hard Drive isn’t showing the same space as it listed according to hard drive manufacturer? A: This is very common question by everybody. T

24This formula calculates a number representing the total number of bytes (characters) that can be stored on the hard drive. This is a decimal number,

257 AppendixRegulatory Compliance FCC Class B Information This equipment has been tested and found to comply with the limits for a Class B digital dev

26Warranty Information Attention: Eagle Tech Computers, Inc. is not responsible for consequential damages, including loss or recovery of data.This pro

27possession of someone other than Eagle Tech. Subject to the limitations specified above, your sole and exclusive warranty shall be, during the perio

28EAGLE TECH MAKES NO GUARANTEE THAT ALL DATA STORED ON EAGLE TECH PRODUCTS IS ALWAYS SECURE WIHOUT ANY RISKS OF DATA LOSS. EAGLE TECH REMINDS YOU TO

21 Getting StartedThank you for purchasing EAGLE | CONSUS W-SERIES product. Eagle | Consus W-Series SATA to USB2.0 & eSATA External Storage System

298 Understand Eagle Tech Brand

3System RequirementsHardware  Pentium® II, 200 MHz equivalent or newer for IBM compatible PC PowerPC G4, 350 MHz or newer for PowerPC-based Apple C

42 Setting UpYou will need a 3.5 inch SATA Hard Drive. Carefully follow the procedure to install the hard drive into the enclosure. Note: For pre-inst

5Hard Drive Installation1. Remove 2 screws from the rear. 2. Unplug (D1A, Red-Black cable) HDD Access LED Connector and unplug (D2A, Blue-Black cabl

63. Pull out the Disk Mounting Tray and slice in the SATA hard drive to the SATA connector on the controller board. 4. Tighten up Hard Drives with 4

75. Plug in the (Red-Black Cable) “HDD Access LED” Connector to D1A and (Blue-Black Cable) “Power LED” Connector to D2A on the controller board.6. S

87. Put the bezel back and tighten up with 2 screws at the rear. 8. External Hard Drive Installation Process Completed!